Máquina de fabricar Tiza / Gis Escolares

Change Language to English

- Molde en bronce de cañón con espigas en cobre sobre placa de fibras de vidrio para expulsión de tizas





Diámetro de tiza (Cima / fondo) (mm):

8 / 11

8 / 11

8 / 11

Alto de tiza (mm):




Numero de tizas por operación:




Tiempo por operación (min.):




Dimensiones (m):

0.7 x 0.7 x 1.6

0.7 x 0.7 x 1.6

0.8 x 0.8 x 1.8

Peso Neto / Bruto (Kgs.):

150 / 250

175 / 275

250 / 400

Volumen del embarque (m3):




Accesorios Estándar: Dos bateas de hierro galvanizado, dos cuchillos, una chapa de goma

chalk stick making machine
Modelo: CM-514





The machine has the following items:

    1. One piece Gun-Metal body mould
    2. Fiber sheet / Aluminium plate with Copper / Brass pins.
    3. G. I. Tray / boxes (two nos.)
    4. Steel knives (two nos.)
    5. One wooden base covered with Rexene cloth.
    6. Rack gear fitted steel fabricated stand with handles to hold Gun-metal mould & Aluminium plate

Other items required to start production (not supplied by us):
i. Jug ii. Pot / Vessel iii. Glass / Mug iv. Cotton Cloth v. Kerosene vi. Mustard Oil vii. Plaster of Paris (raw material) viii. Water
Machine Operation:
1. First of all, clean the machine with Kerosene oil / Petrol to remove all the dust / Grease / oil (except item no. 5 (wooden base) supplied with machine).
2.  Apply fresh Lubricant oil to the Rack-Gears & brackets, which hold the Gun-Metal mould.
3. Apply oil (mixture of Kerosene oil & Mustard oil in 50:50 ratio) at the upper portion of the mould (side having bigger diameter holes) with the help of a brush so that the oil goes down the entire mould.
4. Cover the wooden base with wet cotton cloth, 4-5 folds, and place it on the M. S. plate just below the Gun – Metal mould. Operate the lower handle of machine so that this wooden base with the wet cotton cloth touches / stick to the lower part of the Gun Metal mould (Side where the hole diameter is smaller). Now lock the machine / handle with the lever provided near the handle.
The wet cotton cloth at the base of the mould will prevent leakage of plaster of Paris and will also soak the access water from the mixture of plaster of Paris & water.
5. Now operate the upper handle of the machine & bring the Aluminium plate with Copper / Brass pins to maximum upper limit, to enable pouring of the mixture of Plaster of Paris & water.
6. Preparing the Plaster of Paris Mix: Take a pot / vessel and pour some water in it. Add the Plaster of Paris to this water.
NOTE: Refrain from pouring water over Plaster of Paris as then the water will not mix well and evenly, resulting in lumps.
7. Now stir the mixture of Plaster of Paris & water thoroughly by hand or with a stick as may be convenient to you.
NOTE: Only mix enough quantity of Plaster of Paris & water that may be required for one charge of the mould, as the mixture sets very fast, and once set, becomes unusable. At the same time, see to it that the quantity of mixture is sufficient for one charge of the mould, because, if the mixture is not sufficient and if you make another mix and add it in the mould, you will get breakage of chalks.
8. Pour this mixture from the top of the Gun-metal mould (i.e. from the side where the hole diameter is larger) & allow the mixture to settle down.
9. After 4 to 5 minutes of pouring the mixture into the mould, remove the excess mixture from the top of the mould with the help of the steel knife provided.
10. Remove the wooden base & cotton cloth from under the mould and invert the mould using the lever so that the mould side having larger diameter holes face down.
11. Put the G.I. tray / box on the plate and touch it to the mould.
12. Bring down the Aluminium plate with pins by operating the upper handle of the machine & apply a little pressure.
The pins will press the chalks out of their respective moulds, and the Chalk Sticks will be collected in the G.I. tray.
13. Now, take the Aluminium plate with pins back up by operating the upper handle and remove the G.I. tray (with the ready chalk sticks)
14. Put this tray (with ready chalk sticks) out in the open for drying under the sun. For quicker drying of the chalk sticks, you could use an electric oven.
15. For producing the next batch of chalk sticks, rotate the mould back to its first position (with the side having larger hole diameter facing skywards), lubricate the mould with the 50:50 mixture of Kerosene & Mustard oil, mix the next batch of Plaster of Paris & water, and continue production (from point no. 8 stated above)

- Do not pour the mixture of Plaster of Paris & water into the mould without oiling the mould with a 50:50 mixture of Kerosene & Mustard oil.
- Always prepare just enough mixture of Plaster of Paris for one charge of the mould.
- Always keep wet cotton cloth with 4-5 folds at the bottom of the mould.
- Daily Oil / Lubricate Rack-Gear & moving parts of the machine.
- Use superior quality of Plaster of Paris as it will also give smooth writing of chalk sticks.

Maneklal Global Exports
67 Bajaj Bhavan, Nariman Point, Mumbai - 400021, INDIA
Telf.: +9122-22041340 / 41 / 42. Fax: +9122-22041389
Para hablar en español llame al: +9122-22041390
WhatsApp: +918652695030

e-mail: ventas@maneklalexports.com / MaquinariaManek@gmail.com / Formulario de Consulta

Home  Top


Back   Next